Blazer PB-207 Issue

Boobar · 07-05-2009, 07:55 PM

I need some input from the good folks on the forum who have a Blazer PB-207. I have had this lighter since Christmas and up to a month or so ago it worked great. Now the lighter only lights once in a while. You can click the trigger to ignite the flame and it sparks but the flame never takes hold. Once you let off the trigger you can still here gas escaping from the tip for several seconds. If/when I can ever get it to light, when you let off the trigger the flame stays lit for several seconds.

I have not abused this lighter and I have not dropped it on any hard surfaces.

Any input would be great. I am going to contact the company to see about having it fixed or exchanged out but I thought I would see if anyone on here had a similar issue and if there might be an easy fix.

Thanks

Sauer Grapes · 07-05-2009, 08:08 PM

Sounds to me like it's turned up too much.

Did this start after a refill? Try turning the juice down some.

Silound · 07-05-2009, 08:33 PM

Turn down the flame to the lowest setting possible and click it. If you still hear the gas escaping at the lowest flame setting, then the valve will need adjustment which means dismantling the head assembly.

If you don't hear gas escaping, then turn it up a small amount at a time and click it after each small adjustment. If that STILL doesn't solve the problem, you probably have a clogged filter, which will ALSO require disassembly of the head, but which is far more difficult given the minuscule nature of the filter.

You may need to send it back to Blazer for refitting.

TheTraveler · 07-05-2009, 10:20 PM

I just fixed a torch lighter for a friend.

1. dismantled the lighter and cleaned the nozzle where the gas comes out (held it gently with needle nose pliers and sanded it clean with a fine modeling file

2. tested it; it worked fine. put it back together and it didn't work again.

3. dismantled it again - it worked fine.

grrrr

4. noticed that when I put the metal cover over it the spark started arcing to the lighter body instead of the fuel nozzle. bent the wire a little closer to the nozzle. (I think I bent the wire a little while cleaning the nozzle.)

5. done

If you feel comfortable doing this and the lighter allows you, I recommend cleaning any built-up carbon from the fuel nozzle that may be interfering with spark. Also, look closely to see exactly where that spark is arcing to.

Just my

Also, if this voids a warranty maybe you shouldn't try it.

Good luck!

lightning9191 · 07-06-2009, 10:38 AM

I had this same problem. I removed a small paper filter inside the nozzle assembly....it was pretty dirty. It is really tiny and between two metal screens. I thought about taking pictures of the process a few minutes after I had everything put together.

Process the best I can remember:
1. Unscrew two screws holding top of lighter on.
2. Remove top of lighter and remove small foam filter.
3. On bottom of the top of the lighter (does that make sense?), unscrew center.....if I remember right this is a reverse thread.
4. Inside of there is the small filter I am talking about. Seperate metal screens and remove white paper filter.
5. Put everything back together. There is a small, solid metal piece that goes on top of the filter....towards the flame end.

I'll be happy to do it for you if you want to pay the shipping.

PeteSB75 · 07-06-2009, 07:26 PM

I had the same problem with mine after about the same amount of time. All I did was fully purge the tank. I just pressed and held the metal tube where butane goes in until I heard nothing coming out. After that, I filled it and it worked like a charm. I make sure I purge it fully every couple of times I fill it and have had no problems with mine for more than two years.

Boobar · 07-06-2009, 07:32 PM

Thanks for all the input guys, I will try some of what you suggested and see how it works.

icehog3 · 07-06-2009, 10:17 PM

Quote:

Originally Posted by Boobar

Thanks for all the input guys, I will try some of what you suggested and see how it works.

Let us know, my first Blazer that lasted 4 years needs some help as well.

montecristo#2 · 07-06-2009, 10:58 PM

Quote:

Originally Posted by PeteSB75

I had the same problem with mine after about the same amount of time. All I did was fully purge the tank. I just pressed and held the metal tube where butane goes in until I heard nothing coming out. After that, I filled it and it worked like a charm. I make sure I purge it fully every couple of times I fill it and have had no problems with mine for more than two years.

Yep - had a similar issue. I think I had some issues filling it and got a little too much air in the tank. So I emptied it completely and filled it up again and it worked fine.

This has happened a copy of times, the better I fill it the less issues I have with it lighting afterwards.

I would definitely try this before taking it apart.

Parshooter · 07-07-2009, 07:13 AM

I purge my lighters EVERY time I refill.

poker · 07-07-2009, 07:22 AM

Quote:

Originally Posted by Parshooter

I purge my lighters EVERY time I refill.

I purge all my butane lighters prior to refilling.

lightning9191 · 07-07-2009, 08:33 AM

Quote:

Originally Posted by montecristo#2

Yep - had a similar issue. I think I had some issues filling it and got a little too much air in the tank. So I emptied it completely and filled it up again and it worked fine.

This has happened a copy of times, the better I fill it the less issues I have with it lighting afterwards.

I would definitely try this before taking it apart.

I tried emptying and purging a few times before going further.

yourchoice · 07-07-2009, 08:39 AM

Quote:

Originally Posted by icehog3

Let us know, my first Blazer that lasted 4 years needs some help as well.

I have one that needs work too. I think I may try cleaning the filter described.

Boobar · 07-20-2009, 04:22 PM

UPDATE:

I am still having some issues but I have figured out how to make it work. I am a little uneasy about taking the lighter apart. The first thing I have to do is click the lighter like I am trying to light it but it never lights the first time. I release the igniter button and I listen for when the gas sound stops, usually takes a couple of seconds, and then I have to make sure give a good quick click and then the lighter lights up just fine. This will work for now I guess as I hate to lose such a powerful lighter.

tsolomon · 07-20-2009, 04:43 PM

It's still under warranty, so send it back to Blazer. Had the same problem with a slow leak and sent it back to Blazer. The repair took 3-4 weeks, but now it's is on the fritz again and only lights 1 out of 5 times. I bought a new one and will be sending the old one back again.

gorob23 · 07-20-2009, 05:26 PM

Quote:

Originally Posted by poker

I purge all my butane lighters prior to refilling.

I ask the closet "bookend" to do it for me

Rob

Pat1075 · 07-20-2009, 06:47 PM

If none of that helps spray some electrical contact cleaner in it then let it dry out for a couple minutes. Sometimes its just so caked up with crap from our cigars the burners need something a little more heavy duty than fire to keep them clean

07-20-2009, 07:29 PM

I have the same problem with my xikar lighter. I tried all of the above, purge,lowest setting, to no avail. It's only a month old so I guess I'll be mailing it back.

yourchoice · 07-21-2009, 08:00 AM

I took mine apart last night and tried all kinds of stuff...some recommended here, some not. All to no avail.

M1903A1 · 07-21-2009, 08:15 AM

Quote:

Originally Posted by Parshooter

I purge my lighters EVERY time I refill.

Makes a BIG difference!

07-05-2009, 07:55 PM	#1
Boobar Rubber Room Wall Bouncer Join Date: Oct 2008 First Name: Bob Location: Northcentral PA Posts: 428 Trading: (37)	Blazer PB-207 Issue I need some input from the good folks on the forum who have a Blazer PB-207. I have had this lighter since Christmas and up to a month or so ago it worked great. Now the lighter only lights once in a while. You can click the trigger to ignite the flame and it sparks but the flame never takes hold. Once you let off the trigger you can still here gas escaping from the tip for several seconds. If/when I can ever get it to light, when you let off the trigger the flame stays lit for several seconds. I have not abused this lighter and I have not dropped it on any hard surfaces. Any input would be great. I am going to contact the company to see about having it fixed or exchanged out but I thought I would see if anyone on here had a similar issue and if there might be an easy fix. Thanks __________________ Bob

07-05-2009, 08:33 PM	#3
Silound ex-CS Swamp Gorilla Join Date: Nov 2008 Location: Somewhere in a swamp, south of sanity Posts: 802 Trading: (15)	Re: Blazer PB-207 Issue Turn down the flame to the lowest setting possible and click it. If you still hear the gas escaping at the lowest flame setting, then the valve will need adjustment which means dismantling the head assembly. If you don't hear gas escaping, then turn it up a small amount at a time and click it after each small adjustment. If that STILL doesn't solve the problem, you probably have a clogged filter, which will ALSO require disassembly of the head, but which is far more difficult given the minuscule nature of the filter. You may need to send it back to Blazer for refitting. __________________ Back in black, and better than ever! You can't keep a good gorilla down! LSU Geaux Tigers!

07-05-2009, 10:20 PM	#4
TheTraveler giggity giggitty Join Date: Oct 2008 First Name: Jonathan Location: Near a Walmart Posts: 1,813 Trading: (12)	Re: Blazer PB-207 Issue I just fixed a torch lighter for a friend. 1. dismantled the lighter and cleaned the nozzle where the gas comes out (held it gently with needle nose pliers and sanded it clean with a fine modeling file 2. tested it; it worked fine. put it back together and it didn't work again. 3. dismantled it again - it worked fine. grrrr 4. noticed that when I put the metal cover over it the spark started arcing to the lighter body instead of the fuel nozzle. bent the wire a little closer to the nozzle. (I think I bent the wire a little while cleaning the nozzle.) 5. done If you feel comfortable doing this and the lighter allows you, I recommend cleaning any built-up carbon from the fuel nozzle that may be interfering with spark. Also, look closely to see exactly where that spark is arcing to. Just my Also, if this voids a warranty maybe you shouldn't try it. Good luck! __________________ "My life is my own."

07-06-2009, 10:38 AM	#5
lightning9191 I think I'm normal... Join Date: Oct 2008 First Name: Kevin Posts: 1,007 Trading: (8)	Re: Blazer PB-207 Issue I had this same problem. I removed a small paper filter inside the nozzle assembly....it was pretty dirty. It is really tiny and between two metal screens. I thought about taking pictures of the process a few minutes after I had everything put together. Process the best I can remember: 1. Unscrew two screws holding top of lighter on. 2. Remove top of lighter and remove small foam filter. 3. On bottom of the top of the lighter (does that make sense?), unscrew center.....if I remember right this is a reverse thread. 4. Inside of there is the small filter I am talking about. Seperate metal screens and remove white paper filter. 5. Put everything back together. There is a small, solid metal piece that goes on top of the filter....towards the flame end. I'll be happy to do it for you if you want to pay the shipping. __________________ I eat gummy bears by tearing them limb from limb and eating their heads last.

07-06-2009, 07:26 PM	#6
PeteSB75 Have My Own Room Join Date: Oct 2008 First Name: Pete Location: CT Posts: 1,674 Trading: (18)	Re: Blazer PB-207 Issue I had the same problem with mine after about the same amount of time. All I did was fully purge the tank. I just pressed and held the metal tube where butane goes in until I heard nothing coming out. After that, I filled it and it worked like a charm. I make sure I purge it fully every couple of times I fill it and have had no problems with mine for more than two years. __________________ Formerly Malik23

07-05-2009, 08:08 PM	#2
Sauer Grapes Snatchin' yo people up Join Date: Oct 2008 Posts: 2,235 Trading: (44)	Re: Blazer PB-207 Issue Sounds to me like it's turned up too much. Did this start after a refill? Try turning the juice down some.

07-06-2009, 07:32 PM	#7
Boobar Rubber Room Wall Bouncer Join Date: Oct 2008 First Name: Bob Location: Northcentral PA Posts: 428 Trading: (37)	Re: Blazer PB-207 Issue Thanks for all the input guys, I will try some of what you suggested and see how it works. __________________ Bob

07-07-2009, 07:13 AM	#10
Parshooter I'm a friend of Gary S Join Date: Oct 2008 First Name: Marc Location: St Somewhere Posts: 835 Trading: (2)	Re: Blazer PB-207 Issue I purge my lighters EVERY time I refill. __________________ I love chicks with FLBP.

07-20-2009, 04:22 PM	#14
Boobar Rubber Room Wall Bouncer Join Date: Oct 2008 First Name: Bob Location: Northcentral PA Posts: 428 Trading: (37)	Re: Blazer PB-207 Issue UPDATE: I am still having some issues but I have figured out how to make it work. I am a little uneasy about taking the lighter apart. The first thing I have to do is click the lighter like I am trying to light it but it never lights the first time. I release the igniter button and I listen for when the gas sound stops, usually takes a couple of seconds, and then I have to make sure give a good quick click and then the lighter lights up just fine. This will work for now I guess as I hate to lose such a powerful lighter. __________________ Bob

07-20-2009, 04:43 PM	#15
tsolomon Have My Own Room Join Date: Oct 2008 First Name: Tom Location: The Villages, FL Posts: 1,246 Trading: (31)	Re: Blazer PB-207 Issue It's still under warranty, so send it back to Blazer. Had the same problem with a slow leak and sent it back to Blazer. The repair took 3-4 weeks, but now it's is on the fritz again and only lights 1 out of 5 times. I bought a new one and will be sending the old one back again.

07-20-2009, 06:47 PM	#17
Pat1075 Feeling at Home Join Date: Nov 2008 First Name: Patrick Location: Lakewood, OH Posts: 755 Trading: (11)	Re: Blazer PB-207 Issue If none of that helps spray some electrical contact cleaner in it then let it dry out for a couple minutes. Sometimes its just so caked up with crap from our cigars the burners need something a little more heavy duty than fire to keep them clean

07-20-2009, 07:29 PM	#18
streetglide Guest Posts: n/a	Re: Blazer PB-207 Issue I have the same problem with my xikar lighter. I tried all of the above, purge,lowest setting, to no avail. It's only a month old so I guess I'll be mailing it back.

07-21-2009, 08:00 AM	#19
yourchoice Down the stretch Join Date: Oct 2008 First Name: Joel Location: South Jersey Posts: 4,091 Trading: (36)	Re: Blazer PB-207 Issue I took mine apart last night and tried all kinds of stuff...some recommended here, some not. All to no avail.