Custom Titanium Cigar Punch

After buying a few that where overly large or weight a ton I figured it was time to make my own I make custom Titanium Flashlights as a Hobby and just in the past year have gotten the cigar bug.......hundreds and hundreds of dollars later........LOL those darn cigar auctions!.

[ApexAZ]

Very nice!

[sevans105]

Looks great! Quick question though....how does the punch get cleaned out?

Originally Posted by ApexAZ

Very nice!

Thanks!

Originally Posted by sevans105

Looks great! Quick question though....how does the punch get cleaned out?

Every once in a while with a toothpic Though half the time I seem to just blow them out after punching the hole.

Thanks Mac

[Ncpsycho]

Selling them or just a 1 off

Originally Posted by Ncpsycho

Selling them or just a 1 off

I just put them up on my Flashlight Website to see if I get any interest.

http://macscustoms.com/TiCigarPunch.aspx

[irratebass]

Very nice.

[Shawn hines]

Just curious on how you are making them? Molded or turned? Pretty nice though brother, If I used a punch I might be giving you a call.
I like the size, Kinda used to using small punches....

[BlkDrew]

can you make me a larger version for cutting the caps for cigar rolling?

[Bill86]

What is the size in MM of the punch?

[Fordman4ever]

Just looked at the flash lights on your site, those look amazing. I might have to pick up one of those for work.

[LostAbbott]

I think I will place an order for one of those this afternoon. Is the cutting head ti as well? Or is it ss?
Posted via Mobile Device

OOps double post.

Originally Posted by Shawn hines

Just curious on how you are making them? Molded or turned? Pretty nice though brother, If I used a punch I might be giving you a call.
I like the size, Kinda used to using small punches....

These are Turned on a lathe.

Originally Posted by Bill86

What is the size in MM of the punch?

The inner hole is 1/4 inch or 6.35mm

Originally Posted by LostAbbott

Is the cutting head ti as well? Or is it ss?

It is machined from one peice of 6al-4v grade 5 Titanium.

Originally Posted by BlkDrew

can you make me a larger version for cutting the caps for cigar rolling?

What size cap would you want?


Thanks for the comments!
Mac

Very nice, ima make an order for a couple..

Originally Posted by Fordman4ever

Just looked at the flash lights on your site, those look amazing. I might have to pick up one of those for work.

Thanks

[LostAbbott]

Ok so if it is all ti ho do you get a sharp edge? Or keep a sharp edge? As far as I know from being a knife Guy ti does not hold an edge well. Could you thread the ti and add 440 stainless or something to it? That way you could have a nice sharp edge as well as a way to get the cut caps out.
Posted via Mobile Device

Originally Posted by LostAbbott

Ok so if it is all ti ho do you get a sharp edge? Or keep a sharp edge? As far as I know from being a knife Guy ti does not hold an edge well. Could you thread the ti and add 440 stainless or something to it? That way you could have a nice sharp edge as well as a way to get the cut caps out.
Posted via Mobile Device

There are Titanium knife blade out there and yes the SS variants hold an edge better but where talking about a cigar punch here not a knife blade that is going to be cutting rope and tree branches and such. If the punch needs to be sharpened it would be pretty easy to chuck the punch in a drill and hit it with a stone or some sandpaper.

I could add a SS insert but then that would add cost unless you know a place to purchase SS cigar punch inserts?

Mac

[Bill86]

If there's any chance you would swap the key-loop to the cap side and make an area where you could push out the caps that would be awesome.

Also would you make these in a larger size? Say 9mm

[Taki]

Nice job brother, looks great