Thermoelectric Humidor Cooling - and Vinotemp guts

11-22-2008, 11:03 AM

Posted this on the other site, not sure if everyone is still checking both, so here it is for the archives on CA.

OK all, as some of you know I tackled a project to add a TEC (thermoelectric cooler) to my humidor.

Test one was to completely gut and bash a Vinotemp and install the internals to see what the result was.

Basically, it all worked but the setup was too small. I toyed with the idea of changing the actual cooler, but did not pursue as I found another option.

Here is a picture of the Vinotemp guts (I reccomend demolition of the plastic / foam with a hammer while you trace the wires. If you use a blade, you will undoubtedly cut wires, as I did ). What you are looking at is: the cooler is the bottom left - single fan is the cold side, dual fan is the hot side. Power board is just above that - the little board to the right is the LED board, which also serves as a wiring junction - and then you see the front panel that I have mounted to a piece of spanish cedar - just a prototype but I wanted to ensure I could make the panel look good before I sawed a hole in the humi. Oh yes, the blue wire to the bottom right is the temp probe, and it is in the foam toward the top left of the internal grille in the vino.

Test Two is the setup that I am going with - I found a Supercool 24V setup that was much larger. Here is an overall picture (note, wiring is 'temporary' - very temporary - for purposes of bench testing...

Got it all running. there are some internal temp probes that I did not use (the 'extra' wires you can see). Here is a picture with an IR thermometer showing the cold side temp:

Here is one showing the hot side temp:

Here is the 'face' of it - inside, cold side. (Along with a picture of an Anejo 50 that met its end a couple weekends ago (was a gift) when I took these):

And, here it is installed. I do not have it running just yet as I need to figure out what I will use as a thermostat. I had to add some studs to the back to handle the extra weight, then used a silicone type (odor free, weather proof) sealant on the exterior edges. As for the thermostat, there are a couple options that I have found, just none that I am ready satisfied with just yet:

11-22-2008, 11:03 AM	#1
parafumar Guest Posts: n/a	Thermoelectric Humidor Cooling - and Vinotemp guts Posted this on the other site, not sure if everyone is still checking both, so here it is for the archives on CA. OK all, as some of you know I tackled a project to add a TEC (thermoelectric cooler) to my humidor. Test one was to completely gut and bash a Vinotemp and install the internals to see what the result was. Basically, it all worked but the setup was too small. I toyed with the idea of changing the actual cooler, but did not pursue as I found another option. Here is a picture of the Vinotemp guts (I reccomend demolition of the plastic / foam with a hammer while you trace the wires. If you use a blade, you will undoubtedly cut wires, as I did ). What you are looking at is: the cooler is the bottom left - single fan is the cold side, dual fan is the hot side. Power board is just above that - the little board to the right is the LED board, which also serves as a wiring junction - and then you see the front panel that I have mounted to a piece of spanish cedar - just a prototype but I wanted to ensure I could make the panel look good before I sawed a hole in the humi. Oh yes, the blue wire to the bottom right is the temp probe, and it is in the foam toward the top left of the internal grille in the vino. Test Two is the setup that I am going with - I found a Supercool 24V setup that was much larger. Here is an overall picture (note, wiring is 'temporary' - very temporary - for purposes of bench testing... Got it all running. there are some internal temp probes that I did not use (the 'extra' wires you can see). Here is a picture with an IR thermometer showing the cold side temp: Here is one showing the hot side temp: Here is the 'face' of it - inside, cold side. (Along with a picture of an Anejo 50 that met its end a couple weekends ago (was a gift) when I took these): And, here it is installed. I do not have it running just yet as I need to figure out what I will use as a thermostat. I had to add some studs to the back to handle the extra weight, then used a silicone type (odor free, weather proof) sealant on the exterior edges. As for the thermostat, there are a couple options that I have found, just none that I am ready satisfied with just yet: